V-Tec AT16/C5 Especificações Página 43
- Página / 94
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Si2400
Rev. 1.3 43
8. S Registers
Any register not documented here is reserved and should not be written. Bold selection in bit-mapped registers
indicate default values.
Table 27. S-Register Summary
“S”
Register
Register
Address
(hex)
Name Function Reset
S00 0x00 NR Number of rings before answer; 0 suppresses auto answer.
0x00
S01 0x01 DW Number of seconds modem waits before dialing after going
off-hook (maximum of 109 seconds).
0x03
S02 0x02 CW Number of seconds modem waits for a dial tone before hang-up
added to time specified by DW (maximum of 109 seconds).
0x14
S03 0x03 CLW Duration that the modem waits (53.33 ms units) after loss of car-
rier before hanging up.
0x0E
S04 0x04 TD Both duration and spacing (5/3 ms units) of DTMF dialed tones.
0x30
S05 0x05 OFFPD Duration of off-hook time (5/3 ms units) for pulse dialing.
0x18
S06 0x06 ONPD Duration of on-hook time (5/3 ms units) for pulse dialing.
0x24
S07 0x07 MF1 This is a bit mapped register.
1
0x01
S08 0x08 MNRP Minimum ring period (5/3 ms units).
2
0x0A
S09 0x09 MXRP Maximum ring period (5/3 ms units).
2
0x28
S0A 0x0A ROT Ringer off time (53.333 ms units).
2
0x4B
S0B 0x0B MNRO Minimum ringer off time (10 ms units).
2
0x08
S0C 0x0C MF2 This is a bit mapped register.
1
0x00
S0D 0x0D RPE Ringer off time allowed error (53.333 ms units).
2
0x16
S0E 0x0E DIT Pulse dialing Interdigit time (10 ms units added to a minimum
time of 64 ms).
0x46
S0F 0x0F TEC TIES escape character. Default = +.
0x2B
S10 0x10 TDT TIES delay time (256
z
5/3 ms units).
0x07
S11 0x11 ONHI This is a bit mapped register.
1
0x48
S12 0x12 OFHI This is a bit mapped register.
1
0x40
S13 0x13 MF3 This is a bit mapped register.
1
0x10
S14 0x14 MF4 This is a bit mapped register.
1
0x00
S15 0x15 MLC This is a bit mapped register.
1
0x84
S16 0x16 BTON Busy tone on. Time that the busy tone must be on (10 ms units)
for busy tone detector.
0x32
Notes:
1. These registers are explained in detail in the following section.
2. The ring detector will only detect ringing if the ring burst on/off times meet the settings in MNRP, MXRP, MNRU, ROT,
and REP.
- Features 1
- Applications 1
- Description 1
- Functional Block Diagram 1
- 2 Rev. 1.3 2
- TABLE OF CONTENTS 3
- 1. Electrical Specifications 4
- Table 2. Loop Characteristics 5
- Table 3. DC Characteristics 6
- Table 4. DC Characteristics 6
- Table 5. AC Characteristics 7
- for K-Grade, T 8
- –40 to 85°C for B-Grade) 8
- = –40 to 85°C for B-Grade) 9
- 10 Rev. 1.3 10
- 3. Bill of Materials 11
- 12 Rev. 1.3 12
- 4. Analog Input/Output 13
- 5. Functional Description 14
- 5.1. Digital Interface 15
- 16 Rev. 1.3 16
- 5.3. Low Power Modes 17
- 5.4. Global DAA Operation 17
- 18 Rev. 1.3 18
- Rev. 1.3 19 19
- 20 Rev. 1.3 20
- 5.6. Loop Current Detection 21
- 5.7. Carrier Detect/Loss 21
- 5.8. Overcurrent Detection 21
- 5.11. PCM Data Mode 23
- Figure 10. Signal Routing 24
- 5.12. Analog Codec 25
- 5.14. V.42 HDLC Mode 26
- 5.15. Fast Connect 27
- Table 16. MCKR Configurations 28
- 6.1. Command Line Execution 29
- 30 Rev. 1.3 30
- 6.4. S-Register Control 31
- 32 Rev. 1.3 32
- 6.5.4. A1 34
- 6.5.5. !2 34
- 6.5.6. !7 34
- Table 19. !7 Parameters 35
- Figure 12. !7 Security Timing 36
- Progress 37
- S19 S1A S1B S16 S17 S18 38
- Table 23. DTMF 39
- 7.1. DSP Registers 40
- SE8 SE6 SE5 41
- DSP Reg. Addr 41
- 7.2. Call Progress Filters 42
- 8. S Registers 43
- 44 Rev. 1.3 44
- Rev. 1.3 45 45
- 46 Rev. 1.3 46
- Rev. 1.3 47 47
- 50 Rev. 1.3 50
- Rev. 1.3 51 51
- 52 Rev. 1.3 52
- Rev. 1.3 53 53
- 54 Rev. 1.3 54
- Rev. 1.3 55 55
- 56 Rev. 1.3 56
- 58 Rev. 1.3 58
- Kissoff Tone Detect Length) 58
- Rev. 1.3 59 59
- 60 Rev. 1.3 60
- Rev. 1.3 61 61
- 62 Rev. 1.3 62
- Rev. 1.3 63 63
- Rev. 1.3 65 65
- 66 Rev. 1.3 66
- Rev. 1.3 69 69
- 70 Rev. 1.3 70
- Rev. 1.3 71 71
- 72 Rev. 1.3 72
- Rev. 1.3 73 73
- 74 Rev. 1.3 74
- Rev. 1.3 75 75
- 76 Rev. 1.3 76
- Rev. 1.3 77 77
- DAA Isolation Barrier 78
- Emissions/Immunity 78
- DC Termination 79
- AC Termination 80
- Ringer Impedance 80
- DTMF Dialing 80
- Pulse Dialing 80
- Billing Tone Detection 80
- Symbol Value 81
- In-Circuit Testing 82
- Compliance Test Commands 83
- Introduction 84
- APPENDIX C—UL1950 3RD EDITION 85
- 9. Pin Descriptions: Si2400 86
- Rev. 1.3 87 87
- 10. Pin Descriptions: Si3015 88
- Receive Input 89
- Filter 2 89
- Pin # Pin Name Description 89
- 11. Ordering Guide 90
- Millimeters 91
- Revision 1.1 to Revision 1.2 92
- Revision 1.2 to Revision 1.3 92
- Rev. 1.3 93 93
- CONTACT INFORMATION 94
Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso V-Tec AT16/C5
(19 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais