V-Tec AT16/C5 Especificações Página 47
- Página / 94
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Si2400
Rev. 1.3 47
SDF 0xDF DGSR This is a bit mapped register.
1
0x00
SE0 0xE0 CF1 This is a bit mapped register.
1
0x22
SE1 0xE1 CLK1 This is a bit mapped register.
1
0x07
SE2 0xE2 GPIO This is a bit mapped register.
1
0x00
SE3 0xE3 GPD This is a bit mapped register.
1
0x00
SE4 0xE4 CF5 This is a bit mapped register.
1
0x00
SE5 0xE5 DADL (SE8 = 0x00) Write only definition. DSP register address lower
bits [7:0].
1
0x00
SE5 0xE5 DDL (SE8 = 0x01) Write only definition. DSP data word lower bits
[7:0].
1
0x00
SE5 0xE5 DSP1 (SE8 = 0x02) Read only definition. This is a bit mapped register.
1
0x00
SE5 0xE5 DSP2 (SE8 = 0x02) Write only definition. This is a bit mapped register.
1
0x00
SE6 0xE6 DADH (SE8 = 0x00) Write only definition. DSP register address upper
bits [15:8]
0x00
SE6 0xE6 DDH (SE8 = 0x01) Write only definition. DSP data word upper bits
[13:8]
0x00
SE6 0xE6 DSP3 (SE8 = 0x02) Write only definition. This is a bit mapped register.
1
0x00
SE8 0xE8 DSPR4 Set the mode to define E5 and E6 for low level DSP control.
0x00
SEB 0xEB TPD This is a bit mapped register.
1
0x00
SF0 0xF0 DAA0 This is a bit mapped register.
1
0x00
SF1 0xF1 DAA1 This is a bit mapped register.
1
0x1C
SF2 0xF2 DAA2 This is a bit mapped register.
1
0x00
SF4 0xF4 DAA4 This is a bit mapped register.
1
0x0F
SF5 0xF5 DAA5 This is a bit mapped register.
1
0x08
SF6 0xF6 DAA6 This is a bit mapped register.
1
0x00
SF7 0xF7 DAA7 This is a bit mapped register.
1
0x10
SF8 0xF8 DAA8 This is a bit mapped register.
1
—
SF9 0xF9 DAA9 This is a bit mapped register.
1
0x20
Table 27. S-Register Summary (Continued)
“S”
Register
Register
Address
(hex)
Name Function Reset
Notes:
1. These registers are explained in detail in the following section.
2. The ring detector will only detect ringing if the ring burst on/off times meet the settings in MNRP, MXRP, MNRU, ROT,
and REP.
- Features 1
- Applications 1
- Description 1
- Functional Block Diagram 1
- 2 Rev. 1.3 2
- TABLE OF CONTENTS 3
- 1. Electrical Specifications 4
- Table 2. Loop Characteristics 5
- Table 3. DC Characteristics 6
- Table 4. DC Characteristics 6
- Table 5. AC Characteristics 7
- for K-Grade, T 8
- –40 to 85°C for B-Grade) 8
- = –40 to 85°C for B-Grade) 9
- 10 Rev. 1.3 10
- 3. Bill of Materials 11
- 12 Rev. 1.3 12
- 4. Analog Input/Output 13
- 5. Functional Description 14
- 5.1. Digital Interface 15
- 16 Rev. 1.3 16
- 5.3. Low Power Modes 17
- 5.4. Global DAA Operation 17
- 18 Rev. 1.3 18
- Rev. 1.3 19 19
- 20 Rev. 1.3 20
- 5.6. Loop Current Detection 21
- 5.7. Carrier Detect/Loss 21
- 5.8. Overcurrent Detection 21
- 5.11. PCM Data Mode 23
- Figure 10. Signal Routing 24
- 5.12. Analog Codec 25
- 5.14. V.42 HDLC Mode 26
- 5.15. Fast Connect 27
- Table 16. MCKR Configurations 28
- 6.1. Command Line Execution 29
- 30 Rev. 1.3 30
- 6.4. S-Register Control 31
- 32 Rev. 1.3 32
- 6.5.4. A1 34
- 6.5.5. !2 34
- 6.5.6. !7 34
- Table 19. !7 Parameters 35
- Figure 12. !7 Security Timing 36
- Progress 37
- S19 S1A S1B S16 S17 S18 38
- Table 23. DTMF 39
- 7.1. DSP Registers 40
- SE8 SE6 SE5 41
- DSP Reg. Addr 41
- 7.2. Call Progress Filters 42
- 8. S Registers 43
- 44 Rev. 1.3 44
- Rev. 1.3 45 45
- 46 Rev. 1.3 46
- Rev. 1.3 47 47
- 50 Rev. 1.3 50
- Rev. 1.3 51 51
- 52 Rev. 1.3 52
- Rev. 1.3 53 53
- 54 Rev. 1.3 54
- Rev. 1.3 55 55
- 56 Rev. 1.3 56
- 58 Rev. 1.3 58
- Kissoff Tone Detect Length) 58
- Rev. 1.3 59 59
- 60 Rev. 1.3 60
- Rev. 1.3 61 61
- 62 Rev. 1.3 62
- Rev. 1.3 63 63
- Rev. 1.3 65 65
- 66 Rev. 1.3 66
- Rev. 1.3 69 69
- 70 Rev. 1.3 70
- Rev. 1.3 71 71
- 72 Rev. 1.3 72
- Rev. 1.3 73 73
- 74 Rev. 1.3 74
- Rev. 1.3 75 75
- 76 Rev. 1.3 76
- Rev. 1.3 77 77
- DAA Isolation Barrier 78
- Emissions/Immunity 78
- DC Termination 79
- AC Termination 80
- Ringer Impedance 80
- DTMF Dialing 80
- Pulse Dialing 80
- Billing Tone Detection 80
- Symbol Value 81
- In-Circuit Testing 82
- Compliance Test Commands 83
- Introduction 84
- APPENDIX C—UL1950 3RD EDITION 85
- 9. Pin Descriptions: Si2400 86
- Rev. 1.3 87 87
- 10. Pin Descriptions: Si3015 88
- Receive Input 89
- Filter 2 89
- Pin # Pin Name Description 89
- 11. Ordering Guide 90
- Millimeters 91
- Revision 1.1 to Revision 1.2 92
- Revision 1.2 to Revision 1.3 92
- Rev. 1.3 93 93
- CONTACT INFORMATION 94
Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso V-Tec AT16/C5
(19 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.365 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais